/home/techdatasheets.com/WWW/datasheets_html/444797/datasheet-P2103ACMC

Product Description

http://www.teccor.com

1 - 2

+1 972-580-7777

SIDACtor

Data Book and Design Guide

Product Description

SIDACtor components are solid state crowbar devices designed to protect telecom

equipment during hazardous transient conditions. Capitalizing on the latest in thyristor

advancements, Teccor makes SIDACtor devices with a patented ion implant technology.

This technology ensures effective protection within nanoseconds, up to 5000 A surge

current ratings, and simple solutions for regulatory requirements such as GR 1089,

TIA-968 (formerly known as FCC Part 68), ITU-T K.20, ITU-T K.21, and UL 60950.

Operation

In the standby mode, SIDACtor devices exhibit a high off-state impedance, eliminating

excessive leakage currents and appearing transparent to the circuits they protect. Upon

application of a voltage exceeding the switching voltage (V

), SIDACtor devices crowbar

and simulate a short circuit condition until the current flowing through the device is either

interrupted or drops below the SIDACtor device’s holding current (I

). Once this occurs,

SIDACtor devices reset and return to their high off-state impedance.

V-I Characteristics

Advantages

Compared to surge suppression using other technologies, SIDACtor devices offer absolute

surge protection regardless of the surge current available and the rate of applied voltage

(dv/dt). SIDACtor devices:

• Cannot be damaged by voltage

• Eliminate hysteresis and heat dissipation typically found with clamping devices

• Eliminate voltage overshoot caused by fast-rising transients

• Are non-degenerative

• Will not fatigue

• Have low capacitance, making them ideal for high-speed transmission equipment

DRM

-V

-I

Product Description

Produc

t Sel

cti

1 - 3

http://www.teccor.com

SIDACtor

Data Book and Design Guide

+1 972-580-7777

Applications

When protecting telecommunication circuits, SIDACtor devices are connected across Tip

and Ring for metallic protection and across Tip and Ground and Ring and Ground for

longitudinal protection. They typically are placed behind some type of current-limiting

device, such as Teccor’s F1250T Telelink slow blow fuse. Common applications include:

• Central office line cards (SLICs)

• T-1/E-1, ISDN, and xDSL transmission equipment

• Customer Premises Equipment (CPE) such as phones, modems, and caller ID adjunct

boxes

• PBXs, KSUs, and other switches

• Primary protection including main distribution frames, five-pin modules, building

entrance equipment, and station protection modules

• Data lines and security systems

• CATV line amplifiers and power inserters

• Sprinkler systems

For more information regarding specific applications, design requirements, or surge

suppression, please contact Teccor Electronics directly at +1 972-580-7777 or through our

local area representative. Access Teccor’s web site at http://www.teccor.com or

e-mail us at sidactor.techsales@teccor.com.

Part Number Index

http://www.teccor.com

1 - 6

+1 972-580-7777

SIDACtor

Data Book and Design Guide

Part Number Index

Note: For explanation of part numbers, see "Description of Part Number" on page 1-8.

Part Number

Page

A1220U_4

2-36

A1225U_4

2-36

A2106A_

2-32

A2106U_

2-20

A2106U_6

2-24

A2106Z_

2-40

A5030A_

2-32

A5030U_

2-20

A5030U_6

2-24

A5030Z_

2-40

B1100C_

2-52

B1101U_

2-54

B1101U_4

2-58

B1160C_

2-52

B1161U_

2-54

B1161U_4

2-58

B1200C_

2-52

B1201U_

2-54

B1201U_4

2-58

B2050C_

2-52

B3104U_

2-56

B3164U_

2-56

B3204U_

2-56

F0500T

2-66

F1250T

2-66

F1251T

2-66

P0080E_

2-16

P0080S_

2-4

P0080SA MC

2-8

P0080SC MC

2-6

P0080SD

2-10

P0080Z_

2-44

P0084U_

2-22

P0300E_

2-16

P0300S_

2-4

P0300SA MC

2-8

P0300SC MC

2-6

P0300SD

2-10

P0300Z_

2-44

P0304U_

2-22

P0602A_

2-28

P0602AC MC

2-30

P0602Z_

2-42

P0640E_

2-16

P0640EC MC

2-18

P0640S_

2-4

P0640SC MC

2-6

P0640SD

2-10

P0640Z_

2-44

P0641CA2

2-48

P0641S_

2-46

P0641U_

2-50

P0642S_

2-14

P0644U_

2-22

P0720E_

2-16

P0720S_

2-4

P0720SC MC

2-6

P0720SD

2-10

P0720Z_

2-44

P0721CA2

2-48

P0721S_

2-46

P0721U_

2-50

P0722S_

2-14

P0724U_

2-22

P0900E_

2-16

P0900S_

2-4

P0900SC MC

2-6

P0900SD

2-10

P0900Z_

2-44

P0901CA2

2-48

P0901S_

2-46

P0901U_

2-50

P0902S_

2-14

P0904U_

2-22

P1100E_

2-16

P1100S_

2-4

P1100SC MC

2-6

P1100SD

2-10

P1100Z_

2-44

P1101CA2

2-48

Part Number

Page

P1101S_

2-46

P1101U_

2-50

P1102S_

2-14

P1104U_

2-22

P1200S_

2-38

P1300E_

2-16

P1300S_

2-4

P1300SC MC

2-6

P1300SD

2-10

P1300Z_

2-44

P1304U_

2-22

P1400AD

2-60

P1402A_

2-28

P1402AC MC

2-30

P1402Z_

2-42

P1500E_

2-16

P1500EC MC

2-18

P1500S_

2-4

P1500SC MC

2-6

P1500SD

2-10

P1500Z_

2-44

P1504U_

2-22

P1553A_

2-32

P1553AC MC

2-34

P1553U_

2-20

P1553Z_

2-40

P1556U_

2-24

P1602A_

2-28

P1602AC MC

2-30

P1602Z_

2-42

P1800AD

2-60

P1800E_

2-16

P1800S_

2-4

P1800SC MC

2-6

P1800SD

2-10

P1800Z_

2-44

P1803A_

2-32

P1803AC MC

2-34

P1803U_

2-20

P1803Z_

2-40

Part Number

Page

Part Number Index

1-7

http://www.teccor.com

SIDACtor

Data Book and Design Guide

+1 972-580-7777

Produc

t Sel

cti

P1804U_

2-22

P1806U_

2-24

P1900ME

2-64

P2000AA61

2-26

P2000S_

2-38

P2103A_

2-32

P2103AC MC

2-34

P2103U_

2-20

P2103Z_

2-40

P2106U_

2-24

P2200AA61

2-26

P2202A_

2-28

P2202AC MC

2-30

P2202Z_

2-42

P2300E_

2-16

P2300ME

2-64

P2300S_

2-4

P2300SC MC

2-6

P2300SD

2-10

P2300Z_

2-44

P2304U_

2-22

P2353A_

2-32

P2353AC MC

2-34

P2353U_

2-20

P2353Z_

2-40

P2356U_

2-24

P2400AA61

2-26

P2500AA61

2-26

P2500S_

2-38

P2600E_

2-16

P2600EC MC

2-18

P2600S_

2-4

P2600SC MC

2-6

P2600SD

2-10

P2600Z_

2-44

P2604U_

2-22

P2702A_

2-28

P2702AC MC

2-30

P2702Z_

2-42

P2703A_

2-32

Part Number

Page

P2703AC MC

2-34

P2703U_

2-20

P2703Z_

2-40

P2706U_

2-24

P3000AA61

2-26

P3002A_

2-28

P3002AC MC

2-30

P3002CA

2-12

P3002S_

2-14

P3002Z_

2-42

P3100AD

2-62

P3100E_

2-16

P3100EC MC

2-18

P3100S_

2-4

P3100SC MC

2-6

P3100SD

2-10

P3104U_

2-22

P3100Z_

2-44

P3203A_

2-32

P3203AC MC

2-34

P3203U_

2-20

P3203Z_

2-40

P3206U_

2-24

P3300AA61

2-26

P3403A_

2-32

P3403AC MC

2-34

P3403U_

2-20

P3403Z_

2-40

P3406U_

2-24

P3500E_

2-16

P3500S_

2-4

P3500SC MC

2-6

P3500SD

2-10

P3500Z_

2-44

P3504U_

2-22

P3602A_

2-28

P3602AC MC

2-30

P3602Z_

2-42

P4202A_

2-28

P4202AC MC

2-30

Part Number

Page

P4202Z_

2-42

P4802A_

2-28

P4802AC MC

2-30

P4802Z_

2-42

P5103A_

2-32

P5103AC MC

2-34

P5103U_

2-20

P5106U_

2-24

P6002A_

2-28

P6002AC MC

2-30

P6002AD

2-62

P6002CA

2-12

P6002Z_

2-42

Part Number

Page

Description of Part Number

Produc

t Sel

cti

1 - 9

http://www.teccor.com

SIDACtor

Data Book and Design Guide

+1 972-580-7777

The following illustration shows a description of a sample Battrax device part number.

The following illustration shows a description of a sample asymmetrical SIDACtor device

part number.

B 1

DEVICE TYPE

B = Battrax

PACKAGE TYPE

C = Three-leaded DO-214

U = Six-pin SOIC

CONSTRUCTION VARIABLE

0 = No diode

1 = Diode

4 = Four Battrax Devives

RATING

A = 50 A (10x560 µs)

B = 100 A (10x560 µs)

C = 500 A (2x10 µs)

HOLDING CURRENT

05 = 50 mA

10 = 100 mA

16 = 160 mA

20 = 200 mA

Battrax TYPE

1 = Negative

2 = Positive

3 = Dual

A 1806

DEVICE TYPE

A = Asymmetrical SIDACtor

PACKAGE TYPE

A = TO-220

M = TO-218

U = Six-pin SOIC

LEAD FORM OPTIONS

TO-220 modified type 60, 61, or 62

For U type:

3 = 3 chips

4 = 4 chips

6 = 6 chips

RATING

A = 50 A (10x560 µs)

B = 100 A (10x560 µs)

C = 500 A (2x10 µs)

D = 1000 A (8x20 µs)

E = 3000 A (8x20 µs)

PACKING OPTIONS

AP = Ammo pack

RP = Reel pack

TP = Tube pack

MEDIAN VOLTAGE RATING

1806 = 180 V and 60 V

3 = Three Matched SIDACtor chips

Patented

Electrical Parameters

http://www.teccor.com

1 - 10

+1 972-580-7777

SIDACtor

Data Book and Design Guide

Electrical Parameters

Electrical parameters are based on the following definition of conditions:

• On state (also referred to as the crowbar condition) is the low impedance condition

reached during full conduction and simulates a short circuit.

• Off state (also referred to as the blocking condition) is the high impedance condition prior

to beginning conduction and simulates an open circuit.

Off-state

Capacitance — typical capacitance measured in off state

di/dt

Rate of Rise of Current — maximum rated value of the acceptable rate of

rise in current over time

dv/dt

Rate of Rise of Voltage — rate of applied voltage over time

Switching Current — maximum current required to switch to on state

DRM

Leakage Current — maximum peak off-state current measured at V

DRM

Holding Current — minimum current required to maintain on state

Peak Pulse Current — maximum rated peak impulse current

On-state Current — maximum rated continuous on-state current

TSM

Peak One-cycle Surge Current — maximum rated one-cycle AC current

Switching Voltage — maximum voltage prior to switching to on state

DRM

Peak Off-state Voltage — maximum voltage that can be applied while

maintaining off state

On-state Forward Voltage — maximum forward voltage measured at rated

on-state current

On-state Voltage — maximum voltage measured at rated on-state current

Quality and Reliability

Produc

t Sel

cti

1 - 11

http://www.teccor.com

SIDACtor

Data Book and Design Guide

+1 972-580-7777

Quality and Reliability

It is Teccor’s policy to ship quality products on time. We accomplish this through Total

Quality Management based on the fundamentals of customer focus, continuous

improvement, and people involvement.

In support of this commitment, Teccor applies the following principles:

• Employees shall be respected, involved, informed, and qualified for their job with

appropriate education, training, and experience.

• Customer expectations shall be met or exceeded by consistently shipping products that

meet the agreed specifications, quality levels, quantities, schedules, and test and

reliability parameters.

• Suppliers shall be selected by considering quality, service, delivery, and cost of

ownership.

• Design of products and processes will be driven by customer needs, reliability, and

manufacturability.

It is the responsibility of management to incorporate these principles into policies and

systems.

It is the responsibility of those in leadership roles to coach their staff and to reinforce these

principles.

It is the responsibility of each individual employee to follow the spirit of this statement to

ensure that we meet the primary policy — to ship quality products on time.

Standard Terms and Conditions

1 - 12

http://www.teccor.com

SIDACtor

Data Book and Design Guide

+1 972-580-7777

Standard Terms and Conditions

Supplier shall not be bound by any term proposed by Buyer in the absence of written agreement to such term signed by an

authorized officer of Supplier.

(1) PRICE:

(A) Supplier reserves the right to change product prices at any time but, whenever practicable, Supplier will give Buyer at

least thirty (30) days written notice before the effective date of any price change. Unless Supplier has specifically

agreed in writing, signed by an authorized officer of Supplier, that a quoted price shall not be subject to change for a

certain time, all products shipped on or after the effective date of a price change may be billed at the new price level.

(B) Whenever Supplier agrees to a modification of Buyer's order (which modification must be in writing and signed by an

authorized officer of Supplier), Supplier reserves the right to alter its price, whether or not such price was quoted

as “firm”.

(C) Prices do not include federal, state or local taxes, now or hereafter enacted, applicable to the goods sold. Taxes will

be added by Supplier to the sales prices whenever Supplier has legal obligation to collect them and will be paid by

Buyer as invoiced unless Buyer provides Supplier with a proper tax exemption certificate.

(2) PRODUCTION: Supplier may, at its sole discretion and at any time, withdraw any catalog item from further production without

notice or liability to Buyer.

(3) INTEREST:

(A) All late payments shall bear interest thirty (30) days after the due date stated on the invoice until paid at the lower of one

and one-half percent per month or the maximum rate permitted by law. All interest becoming due shall, if not paid when

due, be added to principal and bear interest from the due date. At Supplier's option, any payment shall be applied first

to interest and then to principal.

(B) It is the intention of the parties to comply with the laws of the jurisdiction governing any agreement between the

parties relating to interest. If any construction of the agreement between the parties indicates a different right given

to Supplier to demand or receive any sum greater than that permissible by law as interest, such as a mistake in

calculation or wording, this paragraph shall override. In any contingency which will cause the interest paid or

agreed to be paid to exceed the maximum rate permitted by law, such excess will be applied to the reduction of

any principal amount due, or if there is no principal amount due, shall be refunded.

(4) TITLE AND DELIVERY: Title to goods ordered by Buyer and risk of loss or damage in transit or thereafter shall pass to Buyer

upon Supplier's delivery of the goods at Supplier's plant or to a common carrier for shipment to Buyer.

(5) CONTINGENCIES: Supplier shall not be responsible for any failure to perform due to causes reasonably beyond its control.

These causes shall include, but not be restricted to, fire, storm, flood, earthquake, explosion, accident, acts of public enemy,

war rebellion, insurrection, sabotage, epidemic, quarantine restrictions, labor disputes, labor shortages, labor slow downs

and sit downs, transportation embargoes, failure or delays in transportation, inability to secure raw materials or machinery for

the manufacture of its devices, acts of God, acts of the Federal Government or any agency thereof, acts of any state or local

government or agency thereof, and judicial action. Similar causes shall excuse Buyer for failure to take goods ordered by

Buyer, from the time Supplier receives written notice from Buyer and for as long as the disabling cause continues, other than

for goods already in transit or specially fabricated and not readily saleable to other buyers.

Supplier assumes no responsibility for any tools, dies, and other equipment furnished Supplier by Buyer.

(6) LIMITED WARRANTY AND EXCLUSIVE REMEDY: Supplier warrants all catalog products to be free from defects in materials

and workmanship under normal and proper use and application for a period of twelve (12) months from the date code on the

product in question (or if none, from the date of delivery to Buyer.) With respect to products assembled, prepared, or manu-

factured to Buyer's specifications, Supplier warrants only that such products will meet Buyer's specifications upon delivery.

As the party responsible for the specifications, Buyer shall be responsible for testing and inspecting the products for adher-

ence to specifications, and Supplier shall have no liability in the absence of such testing and inspection or if the product

passes such testing or inspection. THE ABOVE WARRANTY IS THE ONLY WARRANTY EXTENDED BY SUPPLIER, AND

IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES AND CONDITIONS, EXPRESSED OR IMPLIED (EXCEPT AS

PROVIDED HEREIN AS TO TITLE), ON ANY GOODS OR SERVICES SOLD OR RENDERED BY SUPPLIER, INCLUDING

ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY

WILL NOT CREATE WARRANTY COVERAGE FOR ANY ITEM INTO WHICH ANY PRODUCT SOLD BY SUPPLIER MAY

HAVE BEEN INCORPORATED OR ADDED.

SUPPLIER'S ENTIRE LIABILITY AND BUYER'S EXCLUSIVE REMEDY UNDER THIS WARRANTY SHALL BE, AT

SUPPLIER'S OPTION, EITHER THE REPLACEMENT OF, REPAIR OF, OR ISSUANCE OF CREDIT TO BUYER'S

ACCOUNT WITH SUPPLIER FOR ANY PRODUCTS WHICH ARE PROPERLY RETURNED BY BUYER DURING THE

WARRANTY PERIOD. All returns must comply with the following conditions:

Standard Terms and Conditions

Produc

t Sel

cti

1 - 13

http://www.teccor.com

SIDACtor

Data Book and Design Guide

+1 972-580-7777

(A) Supplier is to be promptly notified in writing upon discovery of defects by Buyer.

(B) Buyer must obtain a Return Material Authorization (RMA) number from the Supplier prior to returning product.

(D) Supplier's examination of such product discloses, to its satisfaction, that such defects have not been caused by

misuse, neglect, improper installation, repair, alteration, or accident.

(E) The product is returned in the form it was delivered with any necessary disassembly carried out by Buyer at Buyer's

expense.

IN NO EVENT SHALL SUPPLIER, OR ANYONE ELSE ASSOCIATED IN THE CREATION OF ANY OF SUPPLIER'S

PRODUCTS OR SERVICES, BE LIABLE TO BUYER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY

NATURE INCLUDING LOSS OF PROFITS, LOSS OF USE, BUSINESS INTERUPTION, AND THE LIKE. BUYER

ACKNOWLEDGES THAT THE ABOVE WARRANTIES AND LIMITATIONS THEREON ARE APPROPRIATE AND

REASONABLE IN EFFECTUATING SUPPLIER'S AND BUYER'S MUTUAL INTENTION TO CONDUCT AN EFFICIENT

TRANSACTION AT PRICES MORE ADVANTAGEOUS TO BUYER THAN WOULD BE AVAILABLE IN THE PRESENCE

OF OTHER WARRANTIES AND ASSURANCES.

(7) PATENTS: Buyer shall notify Supplier in writing of any claim that any product or any part of use thereof furnished under this

agreeme